How Much Does It Cost to Replace a Radius Arm Assembly on a Truck or SUV?

For a U.S. planning estimate, replacing one complete radius arm assembly on a truck or SUV usually costs about $500–$1,200 installed with a quality aftermarket arm or $700–$1,600 with an OE arm. A premium-vehicle, dealer, or corrosion-heavy job can reach $1,200–$2,000 or more per side. Those figures normally include the arm, standard labor, and an alignment check or adjustment, but not every quote includes new hardware, taxes, shop fees, or repairs to related parts.

This is not a universal flat price. “Radius arm” can describe different longitudinal suspension links. A Ford Super Duty radius arm is not the same part or service operation as the rearward lower link often called a radius arm on a Range Rover. Confirm the year, make, model, drivetrain, side, OE reference, and exact failed joint before comparing estimates.

Ford Super Duty long radius arm and Range Rover rearward lower link shown as two different suspension architectures
Two radius arm architectures

Quick Radius Arm Replacement Cost Breakdown

The table below is a 2026 U.S. planning range, not a vehicle-specific quote. It reflects current public parts-price observations, common one-side labor allowances, and normal alignment budgeting. Local rates and actual book time can move the result outside the range.

Cost item, one sideQuality aftermarketOE partWhat changes the number
Radius arm assembly$100–$350$250–$650Vehicle, steel or aluminum construction, included bushing or ball joint, and brand
Standard labor$200–$600$200–$600Book time, shop rate, access, suspension design, and whether bolts release normally
Alignment check/adjustment$100–$250$100–$250Two-wheel versus four-wheel service and local market
Hardware or routine shop supplies$20–$150$20–$150One-time-use fasteners, eccentric hardware, penetrant, and disposal fees
Typical installed total$500–$1,200$700–$1,600Before tax and unrelated repairs

The arithmetic matters more than any national “average.” AAA reports that nearly half of U.S. shops in a recent industry analysis charge roughly $120–$159 per labor hour, while rates can run below $100 or above $200 depending on location and facility type. Its repair guidance also explains that shops commonly multiply a published flat-rate time by the shop’s hourly rate. That is why two competent shops can quote the same job differently without either estimate being automatically wrong. See AAA’s discussion of current mechanic labor rates and regional variation.

Exploded cost stack for parts labor alignment hardware and related repairs in a radius arm quote
Radius arm repair cost stack

Why the Price Changes So Much

The vehicle may use a very different kind of radius arm

On many solid-front-axle Ford Super Duty applications, the radius arm is a long, heavy link between the axle and the frame-side bracket. The arm and its fasteners must manage substantial fore-aft loads from braking, acceleration, axle movement, and road inputs.

On some Land Rover and Range Rover platforms, parts catalogues and workshops may use “radius arm,” “rearward lower control arm,” or “tension strut” for a link that locates the wheel longitudinally. That assembly may include a large compliant or hydraulic bushing and a ball joint. Our guide to tension strut bushing load paths and terminology explains why names alone are not enough to identify the component.

If your estimate simply says “control arm,” ask for the position and OE number. For a broader price discussion covering other arm types, use the separate control arm replacement cost guide.

OE and quality aftermarket assemblies are not priced the same

An OE assembly normally offers a known geometry, joint package, bushing orientation, and vehicle-program match. A quality aftermarket assembly may lower the parts cost, but the useful comparison is not logo versus logo. Ask whether the replacement matches:

  • the correct mounting centers and arm geometry;
  • the required left- or right-side configuration;
  • the original bushing type, including any hydraulic design;
  • ball-joint and hardware scope;
  • stated vehicle and production-date fitment; and
  • a meaningful parts-and-labor warranty.

A very low purchase price has little value if the arm creates alignment difficulty, transmits more vibration, or has to be replaced again.

Corrosion can turn a book-time job into a fabrication job

Normal labor assumes the fasteners can be removed with standard service methods. On an older truck or a vehicle operated in a road-salt region, a bolt can seize to the inner sleeve of the bushing. The shop may need additional heat, cutting, extraction, or replacement hardware. Damage at the frame bracket, axle bracket, or mounting hole can expand the scope again.

Ask the shop to state in writing how it will authorize corrosion-related labor. A fair estimate can include a base price and a clearly defined contingency instead of hiding an unlimited “extra labor” line.

Alignment may be a separate charge

A radius arm influences the wheel or axle’s fore-aft location and can affect caster or other alignment relationships. The exact adjustment path is platform-specific, but the estimate should say whether it includes:

  • an alignment measurement only;
  • front alignment adjustment;
  • a complete four-wheel alignment; or
  • additional correction hardware.

Do not assume an alignment is included because the arm price looks high.

Bushing Only or Complete Radius Arm?

A bushing may cost much less than a complete arm, but the correct comparison is total installed cost, not the price of the rubber-metal part by itself.

CheckBushing-only repair may make senseComplete arm is usually the stronger decision
Arm bodyStraight, corrosion-free, and dimensionally soundBent, cracked, heavily corroded, or damaged at a bore or mount
Other jointReusable and within specificationBall joint or second bushing is worn, loose, or damaged
ServiceabilityCorrect bushing is available and the arm supports controlled removal/pressingBushing is not serviced separately or removal risks damaging the arm
LaborPress tooling and technician experience are availablePress work plus cleanup approaches the cost of an assembled arm
Engineering matchGeometry, orientation, and performance specification are knownReplacement bushing identity or installation orientation is uncertain

For planning, a bushing-only job may land around $300–$800 per side, but it can exceed that range when the arm is difficult to remove, the old shell must be cut out, or the new bushing requires careful directional positioning. Replacing the assembly can be cheaper overall when it renews the bushing and another wear joint in one operation.

Decision tree comparing bushing-only repair with complete radius arm replacement
Bushing or complete arm decision

Installation Details That Protect the New Part

The replacement part is only one part of the result. Installation position and clamp condition can decide whether the new bushing works as intended.

Rubber bushings that twist as the suspension moves should normally be clamped in the vehicle position specified by the OEM. Tightening at full droop when the procedure requires normal ride height can leave the rubber pre-twisted at rest. An official Jaguar Land Rover service instruction for a lower-control-arm fastener specifically requires tightening with the vehicle’s weight on the suspension, while also requiring new fasteners and the correct bolt orientation. The lesson is not to copy that torque procedure to another vehicle; it is to follow the applicable OEM installation sequence and loaded-position requirements.

The shop should also verify fastener condition, bracket integrity, and specified torque method. Reusing an angle-tightened fastener or substituting an unknown bolt can change clamp load. That is a component-retention issue, not a cosmetic detail.

Technician tightening a radius arm bushing at normal vehicle ride height with bolt orientation marked
Correct loaded-position tightening

Why Bushing Specification Affects Value, Not Just Comfort

The frame-side bushing has to control fore-aft motion while filtering impact and road vibration. Its response can differ by direction, displacement amplitude, frequency, and temperature. A part can fit the bracket and still produce a different steering or NVH result if its rubber compound, void geometry, hydraulic passages, or bond system changes.

That is why “same dimensions” is not a complete engineering specification. ISO 4664-1:2022 describes free- and forced-vibration approaches for determining the dynamic properties of vulcanized or thermoplastic rubber at both material and product level. For an OE or validated replacement programme, relevant evidence may include static stiffness, dynamic stiffness under defined conditions, fatigue, environmental aging, rubber-to-metal adhesion, and vehicle-level confirmation.

GJBUSH approaches these parts as rubber-to-metal NVH components rather than simple commodity inserts. The automotive NVH solutions platform is the relevant starting point when a project needs a bushing or arm-level engineering review.

How to Compare Two Written Quotes

Ask both shops to quote the same scope. A useful estimate should identify:

  1. Vehicle year, model, drivetrain, side, and VIN-dependent fitment.
  2. The exact arm position and part number.
  3. OE or named quality-aftermarket part, including warranty.
  4. Billable labor time and hourly rate.
  5. New bolts, nuts, eccentric washers, or other required hardware.
  6. Alignment measurement and adjustment scope.
  7. Treatment of seized hardware or damaged mounting points.
  8. Any ball joint, tire, opposite-side, or related suspension work quoted separately.
  9. Taxes and shop fees needed to reach the out-the-door total.

AAA encourages vehicle owners to obtain a detailed written estimate, and its guidance distinguishes parts and labor rather than reducing a repair to one unexplained number. That same discipline makes radius arm quotes much easier to compare.

Do not approve automatic left-and-right replacement solely because one side failed. Inspect the opposite side for cracking, fluid leakage, separation, excess movement, joint wear, and measurable geometry or compliance differences. Replace both when the evidence or the vehicle-specific procedure supports it—not because “suspension parts always come in pairs.”

From Replacement Quote to OE Supply Decision

For an OE, Tier 1, fleet, or engineered replacement programme, the cost question continues beyond the first invoice. The approved performance has to survive the move from sample to serial production.

A supplier review should connect the drawing and performance targets to compound control, metal preparation, bonding, molding, inspection, test conditions, batch traceability, and formal change control. AIAG’s current APQP guidance explicitly adds emphasis on sourcing, change management, risk mitigation, gated management, and part traceability. See the AIAG overview of APQP and Control Plan expectations.

OE development flow from vehicle inputs and drawing review through bushing validation PPAP and serial production control
Radius arm bushing development and validation flow

For an engineering review, provide:

  • vehicle year, make, model, drivetrain, side, and OE reference;
  • the arm drawing, interface dimensions, or a physical sample;
  • load directions and target static or dynamic stiffness where available;
  • temperature, fluid, corrosion, road, and durability conditions;
  • validation and documentation requirements;
  • prototype and serial quantities; and
  • the required project timing.

These inputs allow the team to separate a simple dimensional replacement from a controlled NVH and durability programme.

Frequently Asked Questions

Is $1,000 a reasonable price for one radius arm?

Yes, $1,000 can be reasonable if the quote includes a quality or OE assembly, two to four billable hours at the local rate, new hardware, and alignment. It may be high for a simple rust-free truck with an inexpensive arm, but low for a premium SUV, dealer repair, seized hardware, or related joint damage. Compare the written scope, not the total alone.

Should radius arms be replaced in pairs?

Not automatically. Inspect the opposite side and replace it when there is evidence of similar wear, leakage, separation, joint play, damage, or a vehicle-specific requirement. One alignment after a justified two-side repair may be more efficient than two separate visits, but efficiency is not proof that the second arm has failed.

Is an alignment required after radius arm replacement?

An alignment check is prudent because the arm helps locate the wheel or axle longitudinally. Whether adjustment is mandatory depends on the vehicle, the fasteners disturbed, and the OEM procedure. Ask the shop to state the alignment scope in the estimate.

Can a shop replace only the radius arm bushing?

Sometimes. The arm must be structurally sound, the correct bushing must be serviceable separately, and the shop needs appropriate removal and installation tooling. Compare the complete installed bushing cost with a complete arm that may also renew another joint.

References

Ready to Partner with GJBUSH?

For us to quickly understand your request and give the exact price. Please provide your detailed inquiry list.With the following information:
1. Part number with the QTY you need
2. Any special requirements please tell us, we do our best to meet your requirement

The more information you give, the more we can easily understand your request fast and give the goods you want.

However, if you only want to know the price, send your list, and our sales will contact you to get your detailed request.

Scroll to Top

Have a Complex NVH Challenge?

Our senior engineers specialize in custom rubber damping solutions. Share your project requirements, and let's engineer the right component for you.